| Author |
Message |
Pari
Guest
|
 Posted:
Tue Oct 25, 2005 4:50 pm Post subject:
DCOM was unable to communicate |
|
|
I am trying to install single node cluster with Win 2003 ent x64 bit.
Installation goes fine, however at the last step of the install when it tries
to connect to the cluster, it gives an error as below:
ERROR:
The Cluster Service on node 'xxxxxxxxxxxxx' cannot be started. The network
path was not found.
In the event log, I see the folllowing:
DCOM was unable to communicate with the computer using any of the configured
protocols.
Does the 'xxxxxxxxxxxxx' be another physical box, beisdes my single node
where I am setting this up?
Can I do all the config on a single node server with a separate domain
controller box? |
|
| Back to top |
|
 |
Pari
Guest
|
| Posted:
Tue Oct 25, 2005 8:50 pm Post subject:
Re: DCOM was unable to communicate |
|
|
I made sure that I add DCOM from the add/remove programs. Its installed. Do I
need to do anything additional to enable this?
"Chuck Timon [MSFT]" wrote:
| Quote: | Ensure DCOM is enabled on the node.
--
Chuck Timon, Jr.
Microsoft Corporation
CCS Beta Engineer
This posting is provided "AS IS" with no
warranties, and confers no rights.
"Pari" <Pari@discussions.microsoft.com> wrote in message
news:435A219D-BF68-48D7-BE8D-388F172D25E9@microsoft.com...
I am trying to install single node cluster with Win 2003 ent x64 bit.
Installation goes fine, however at the last step of the install when it
tries
to connect to the cluster, it gives an error as below:
ERROR:
The Cluster Service on node 'xxxxxxxxxxxxx' cannot be started. The network
path was not found.
In the event log, I see the folllowing:
DCOM was unable to communicate with the computer using any of the
configured
protocols.
Does the 'xxxxxxxxxxxxx' be another physical box, beisdes my single node
where I am setting this up?
Can I do all the config on a single node server with a separate domain
controller box?
|
|
|
| Back to top |
|
|
Chuck Timon [MSFT]
Guest
|
| Posted:
Tue Oct 25, 2005 8:50 pm Post subject:
Re: DCOM was unable to communicate |
|
|
Ensure DCOM is enabled on the node.
--
Chuck Timon, Jr.
Microsoft Corporation
CCS Beta Engineer
This posting is provided "AS IS" with no
warranties, and confers no rights.
"Pari" <Pari@discussions.microsoft.com> wrote in message
news:435A219D-BF68-48D7-BE8D-388F172D25E9@microsoft.com...
| Quote: | I am trying to install single node cluster with Win 2003 ent x64 bit.
Installation goes fine, however at the last step of the install when it
tries
to connect to the cluster, it gives an error as below:
ERROR:
The Cluster Service on node 'xxxxxxxxxxxxx' cannot be started. The network
path was not found.
In the event log, I see the folllowing:
DCOM was unable to communicate with the computer using any of the
configured
protocols.
Does the 'xxxxxxxxxxxxx' be another physical box, beisdes my single node
where I am setting this up?
Can I do all the config on a single node server with a separate domain
controller box? |
|
|
| Back to top |
|
|
Chuck Timon [MSFT]
Guest
|
| Posted:
Wed Oct 26, 2005 12:50 pm Post subject:
Re: DCOM was unable to communicate |
|
|
The following registry string value is used to enable or disable DCOM on all
operating systems:
HKEY_LOCAL_MACHINE\Software\Microsoft\OLE\EnableDCOM
If you change this value to "N", you disable DCOM after you restart the
operating system.
--
Chuck Timon, Jr.
Microsoft Corporation
CCS Beta Engineer
This posting is provided "AS IS" with no
warranties, and confers no rights.
"Pari" <Pari@discussions.microsoft.com> wrote in message
news:A9CDB6B3-4AEE-4CE7-8A9C-9D5666B9FBEA@microsoft.com...
| Quote: | I made sure that I add DCOM from the add/remove programs. Its installed. Do
I
need to do anything additional to enable this?
"Chuck Timon [MSFT]" wrote:
Ensure DCOM is enabled on the node.
--
Chuck Timon, Jr.
Microsoft Corporation
CCS Beta Engineer
This posting is provided "AS IS" with no
warranties, and confers no rights.
"Pari" <Pari@discussions.microsoft.com> wrote in message
news:435A219D-BF68-48D7-BE8D-388F172D25E9@microsoft.com...
I am trying to install single node cluster with Win 2003 ent x64 bit.
Installation goes fine, however at the last step of the install when it
tries
to connect to the cluster, it gives an error as below:
ERROR:
The Cluster Service on node 'xxxxxxxxxxxxx' cannot be started. The
network
path was not found.
In the event log, I see the folllowing:
DCOM was unable to communicate with the computer using any of the
configured
protocols.
Does the 'xxxxxxxxxxxxx' be another physical box, beisdes my single
node
where I am setting this up?
Can I do all the config on a single node server with a separate domain
controller box?
|
|
|
| Back to top |
|
|
Pari
Guest
|
| Posted:
Wed Oct 26, 2005 4:51 pm Post subject:
Re: DCOM was unable to communicate |
|
|
I enabled the DCOM from component services, checked the registry value was
'Y', rebooted the server, however I still get the same error when it tries to
connect to the cluster. Ans the same error in the event log.
How do I troubleshoot this?
"Chuck Timon [MSFT]" wrote:
| Quote: | The following registry string value is used to enable or disable DCOM on all
operating systems:
HKEY_LOCAL_MACHINE\Software\Microsoft\OLE\EnableDCOM
If you change this value to "N", you disable DCOM after you restart the
operating system.
--
Chuck Timon, Jr.
Microsoft Corporation
CCS Beta Engineer
This posting is provided "AS IS" with no
warranties, and confers no rights.
"Pari" <Pari@discussions.microsoft.com> wrote in message
news:A9CDB6B3-4AEE-4CE7-8A9C-9D5666B9FBEA@microsoft.com...
I made sure that I add DCOM from the add/remove programs. Its installed. Do
I
need to do anything additional to enable this?
"Chuck Timon [MSFT]" wrote:
Ensure DCOM is enabled on the node.
--
Chuck Timon, Jr.
Microsoft Corporation
CCS Beta Engineer
This posting is provided "AS IS" with no
warranties, and confers no rights.
"Pari" <Pari@discussions.microsoft.com> wrote in message
news:435A219D-BF68-48D7-BE8D-388F172D25E9@microsoft.com...
I am trying to install single node cluster with Win 2003 ent x64 bit.
Installation goes fine, however at the last step of the install when it
tries
to connect to the cluster, it gives an error as below:
ERROR:
The Cluster Service on node 'xxxxxxxxxxxxx' cannot be started. The
network
path was not found.
In the event log, I see the folllowing:
DCOM was unable to communicate with the computer using any of the
configured
protocols.
Does the 'xxxxxxxxxxxxx' be another physical box, beisdes my single
node
where I am setting this up?
Can I do all the config on a single node server with a separate domain
controller box?
|
|
|
| Back to top |
|
|
Chuck Timon [MSFT]
Guest
|
| Posted:
Wed Oct 26, 2005 8:50 pm Post subject:
Re: DCOM was unable to communicate |
|
|
Time to open a case with our support personnel.
--
Chuck Timon, Jr.
Microsoft Corporation
CCS Beta Engineer
This posting is provided "AS IS" with no
warranties, and confers no rights.
"Pari" <Pari@discussions.microsoft.com> wrote in message
news:8A1A07DD-6206-4D39-BD52-FEBB1232B4C6@microsoft.com...
| Quote: | I enabled the DCOM from component services, checked the registry value was
'Y', rebooted the server, however I still get the same error when it tries
to
connect to the cluster. Ans the same error in the event log.
How do I troubleshoot this?
"Chuck Timon [MSFT]" wrote:
The following registry string value is used to enable or disable DCOM on
all
operating systems:
HKEY_LOCAL_MACHINE\Software\Microsoft\OLE\EnableDCOM
If you change this value to "N", you disable DCOM after you restart the
operating system.
--
Chuck Timon, Jr.
Microsoft Corporation
CCS Beta Engineer
This posting is provided "AS IS" with no
warranties, and confers no rights.
"Pari" <Pari@discussions.microsoft.com> wrote in message
news:A9CDB6B3-4AEE-4CE7-8A9C-9D5666B9FBEA@microsoft.com...
I made sure that I add DCOM from the add/remove programs. Its installed.
Do
I
need to do anything additional to enable this?
"Chuck Timon [MSFT]" wrote:
Ensure DCOM is enabled on the node.
--
Chuck Timon, Jr.
Microsoft Corporation
CCS Beta Engineer
This posting is provided "AS IS" with no
warranties, and confers no rights.
"Pari" <Pari@discussions.microsoft.com> wrote in message
news:435A219D-BF68-48D7-BE8D-388F172D25E9@microsoft.com...
I am trying to install single node cluster with Win 2003 ent x64 bit.
Installation goes fine, however at the last step of the install when
it
tries
to connect to the cluster, it gives an error as below:
ERROR:
The Cluster Service on node 'xxxxxxxxxxxxx' cannot be started. The
network
path was not found.
In the event log, I see the folllowing:
DCOM was unable to communicate with the computer using any of the
configured
protocols.
Does the 'xxxxxxxxxxxxx' be another physical box, beisdes my single
node
where I am setting this up?
Can I do all the config on a single node server with a separate
domain
controller box?
|
|
|
| Back to top |
|
|
|
|
|
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in